Renia Aquilim 315 is a water-based adhesive that bonds firmly and flexibly. It contains no solvents, so it releases no solvent fumes in your workshop or studio.
When is it most useful?
When is it not suitable?
You can apply it by brush, roller or spray; for smaller areas we recommend the Reusable Glue Spreaders #3431-00. The adhesive must not freeze, so store it in a warm place.
To check which glue suits your pair of materials, use the Which glue for which material tool.
Aquilim 315 has no odour, so I can open it in the evening at my workbench and do not have to air the whole flat the next day. It is enough for everyday small leather goods. The bond is flexible and strong and did not let me down even under heavier load. It turns clear in a short while.
It only reaches full strength after a few days and does not take well to frost, which you need to allow for when planning work and when storing it. It costs a little more than ordinary adhesives.
Enter your email and we'll send you one notification when this product is back in stock. Nothing more.
No. The word “Stand” followed by a date (for example “Stand 08/2021”) is neither an expiry date nor a production date. It marks the label version, i.e. the date on which the manufacturer Renia approved its design and legal wording.
Renia uses it to keep up with ongoing changes to EU legislation on chemical products, such as the CLP Regulation. The date shows which requirements the label was created under. It has nothing to do with when the tin was filled or how old its contents are.
The manufacturer Renia guarantees the technical properties of its products for 12 months from production. Renia usually produces fresh to order, so in practice you can count the 12 months roughly from delivery.
When stored properly, the products remain usable much longer. According to the manufacturer, the properties of most of them usually do not change for another 2–3 years.
The manufacturer is not required to state a production date or a best-before date on these chemical products.
Treat a glued joint on a collar or leash as a supporting one. Without additional hardeners, the manufacturer does not declare water resistance for our Renia glues.
Bending: the manufacturer explicitly states that the dried film stays very flexible only for Aquilim 315.
Water: according to the manufacturer, Aquilim 315 is significantly more resistant with Renia A300 hardener, but we do not sell it. The technical data sheet for Top-Fit and Colle de Cologne does not state water resistance.
Loctite 401 instant glue retained 75 % of its original strength after 1,000 hours in water in the manufacturer's test.
For stressed spots that get wet, add stitching or rivets to the glue.
Thin the Top-Fit and Colle de Cologne contact cements with Renia thinner, not with acetone. Thin Aquilim 315 with a small amount of water.
Cleaning tools: clean the brush and the container with Renia thinner or acetone after using contact cement, and with water after using Aquilim 315.
The thinner does not change the open time of the glue. If you mix it in thoroughly, the glue will not separate afterwards.
According to the manufacturer, Renia glues last at least 12 months at 20 °C. You will find more about storage in the answer How long does Renia glue or dye last?
Top-Fit is the fastest, Colle de Cologne the most universal, and Aquilim 315 is solvent-free.
Top-Fit: contact cement with very high initial tack, so you work on the piece right after joining. It bonds leather, rubber, EVA, felt and cork. It does not bond plasticised PVC.
Colle de Cologne: universal contact cement; you can handle the piece after a few minutes. It also bonds fabric, metal and plasticised PVC (vinyl).
Aquilim 315: water-based and solvent-free. The dried film stays very flexible and transparent. It dries in 30 to 60 minutes and reaches maximum strength after 2 days.
All three bond leather to leather. The choice depends on what you are bonding to the leather and whether you want to work without solvents.
Contact cement contains solvents and you coat both parts with it. Water-based glue is solvent-free, but it dries more slowly.
Contact cement (Top-Fit, Colle de Cologne): solvent-based and highly flammable. Thin and clean it with Renia thinner.
Water-based (Aquilim 315): solvent-free, and the manufacturer does not classify it as hazardous. It dries in 30 to 60 minutes, and once it turns clear it is dry. Wash your tools with water. It must not freeze.
When you glue absorbent leather to a dense material, coat only the dense side with Aquilim 315 and join the parts within a few minutes. You will find the explanation and the procedure in the Aquilim 315 technical data sheet.
For leather to leather, use Renia Top-Fit. It grips straight after joining, so you can carry on working on the piece right away.
Leather with waterproof PVC-coated webbing: Renia Colle de Cologne. According to the manufacturer, Top-Fit does not bond plasticised PVC.
Solvent-free: Renia Aquilim 315, water-based. It dries more slowly, in 30 to 60 minutes.
Small metal part on leather: Loctite 401 instant glue.
For any other pair of materials, the tool Which glue for which material will pick the glue for you.