Double Cap Rivet – Stainless Steel (1000 pcs)

Product code: SS 66 Z
In Stock 136 packs
This two-part double cap saddlery rivet has a very useful notch near the tip of the stem, which lets you rivet belts, collars and harnesses faster and makes the join stronger. Use double cap rivets where both sides of the rivet will be visible, or where the rivet comes in contact with other surfaces (purse and other handles, leashes, collars, harnesses, …). The price listed is for the entire package (1000 pcs).

Choose the right tool both for punching the hole and for setting the rivet. Punch the hole with a hole punch or drive punch whose diameter matches the diameter of the rivet stem (dimension A). Set the rivet with the #3990-00 hand press and a die; without a press, use a hand setter. Always choose the size of the die or setter according to the rivet size. You will find suitable tools among the recommended products below.

IMPORTANT NOTICE – APPLIES ONLY TO STAINLESS STEEL RIVETS

Stainless steel is hard: choose the right tool, otherwise the rivet cap may deform.

Stainless steel is much harder than brass or ordinary steel, so setting these rivets takes more force. Based on our own testing, we recommend:

  • Hand press with foot pedal linkage: use the hand press (#3990-00) with the foot pedal linkage (#3990-TAH) and setting dies (#3997-20 Z). With your foot, you apply much more force and greatly reduce the risk of a deformed cap.
  • Setter with anvil (#8101-20 Z): you can set these rivets well even by hand with a hammer. Rest the cap in the shallower recess of the anvil, which matches the flatter profile of the stainless steel cap.
  • Powered press: use a press with enough force to set these rivets.

We do not recommend the rivet setter (#RS/6x100) with the universal anvil (#RA/40x100-6) for stainless steel rivets. The anvil's recesses are too deep for the stainless steel cap, and the cap deforms in them. For softer brass and steel rivets, you can use the anvil without worry.

Properties

Material · Stainless steel (AISI 304)

304 stainless steel resists rain, sweat and mud with no special care

Low skin-reaction risk on direct contact

Working with it

The bite near the tip of the post speeds up riveting and strengthens the joint

Use

Both sides show, so it suits collars, leashes, bag handles and harnesses

Sizes

Four shank lengths from 7 to 12 mm for different material thicknesses

More information

Product code SS 66 Z
Weight 420 g

Blog post: Riveting guide

Product variants and parameters
All variants
Shank diameter: 3 mm Quantity per Pack: 1000
7 mm 7 mm
8 mm 8 mm
8 mm 10 mm
10 mm 10 mm
Out of stock 10 mm 12 mm
12 mm 12 mm
Dimensions may vary by ±10%

Enter a quantity to see the total price incl. 21% VAT

Total for 1 pack 104.33 €

Added!

  • 1

    Base price from 1 pack 104.32 €/1000 pcs

  • 10

    Package price from 10 packs 59.61 €/1000 pcs 43% cheaper per pack

  • 30

    Carton price from 30 packs 53.65 €/1000 pcs 49% cheaper per pack Lowest price per pack

About us Hardware, leather and tools under one roof. For collars, leashes, halters, belts and handbags.

Why buy from Pet Hardware®

We'll let you know when it's back

Enter your email and we'll send you one notification when this product is back in stock. Nothing more.

Frequently asked questions

Yes, the smallest quantity is one bag of rivets or 100 snaps. We don't offer smaller packs.

  • Rivets and Chicago screws are sold in bags. Most bags contain 100 pcs, bags of rhinestone rivets also 50 pcs, and bags of eyelets and cap rivets usually 1,000 pcs. Brass and stainless steel Chicago screws and some double cap rivets also come in bags of 10.

  • Snap fasteners and button studs are sold individually, from 100 pcs of one type.

The number of pieces per bag and the price per piece are shown on each product. We'll send you a sample to try. See Can I get a product sample?

The total thickness of the layers you're joining decides. Add the shank overhang needed for spreading: the shank should be 2–3 mm longer than the material thickness.

The shank length is listed on each rivet's product page in the variants table as dimension B. The full range is in the Rivets & Screws category.

The hole diameter differs by material. For leather, choose a punch slightly smaller than the shank diameter: leather is elastic and grips the shank tightly. For waterproof webbing, choose a punch that matches the shank exactly; the webbing doesn't stretch, so the shank has to pass through without being forced.

A shank that's too long shows up as a rivet that deforms while spreading, or caps that don't line up.

Often bought together